Analysis of the Efficiency of Heat-Exchangers – Heat Recovery Units for Energy Technology Systems and Units
DOI:
https://doi.org/10.20998/2078-774X.2016.10.08Анотація
Consideration was given to the influence produced by the distribution of the local intensities of heat exchange on the efficiency of heat exchangers with cross and mixed currents. Mathematical models, methods and algorithms were developed to calculate and analyze complicated heat exchangers designed for the heat recovery. Proposed methods give us an opportunity to define the actual functionality of the recuperators in different modes taking into consideration operation factors. Improved computing methods and tools allow us to extent the life of recuperators, analyze the influences produced on the functionality and engineering-and-economical performances of the system, reduce the consumption of fuel-energy resources and material resources and reduce the negative influence of high-temperature energotechnological processes on the environment. Developed models can be used in the future to solve optimization problems related to the design and improvement of the recuperators-recovery units.Посилання
Piir, A. Je. (2004), "The results of experimental and theoretical investigations ofthebeamsbimetallicfinnedtubes",Teplomassoobmen – MMF-2004 [Heat and Mass Transfer - IDF 2004], V Min.mezhdunar.Forum[VMin.Intern.forum], Minsk, Belarus, 24-28 May 2004, vol. 2, pp. 317–318.
Kejs, V. M. and London, A. L. (1967), Kompaktnye teploobmenniki [Compact Heat exchangers], Translated by Sidorova,V.Ja.,in Petrovskogo, Yu.V. (ed.), Jenergija, Moscow, Russia.
Galushcak, I. V., Gorbatenko, V. Ya. and Shevelev, A. A. (2012), “Numerical Investigation of Heat Transfer tu a TubewithPushed Spiral-Tape Finning under a Transverse Flow of Gases”, Thermal Engineering, vol. 59, no. 1, pp. 70–74.
Spravochnik po teploobmennikam: v 2 t [Handbook of heat exchangers: in 2 volumes], Translated by Petuhova, B. S.,inShikova, V. K. (ed.), Jenergoatomizdat, Moscow, Russia.
Kanevec, G. E., Zajcev, I. D. and Golovach, I. I. (1985), Vvedenie v avtomatizirovannoe proektirovanieteploobmennogooborudovanija [Introduction to computer-aided design of heat exchange equipment],Nauk.dumka, Kiev, Ukraine.
Gres, L. P. (2004), Jenergosberezhenie pri nagreve domennogo dut'ja [Energy savings in heating blast air],Porogi,Dnepropetrovsk, Ukraine.
Ulahovich, V.A. (1991), Vyplavka chuguna v moshhnyh metallurgicheskih pechah [Smelting iron in high-powermetallurgicalfurnaces], Metallurgija, Moscow, Russia.
Hanzha, A. M. and Marchenko, N. A. (2010), “Computer modeling of processes in complex heat exchangers”,VestnykNatsyonal'noho tekhnycheskoho unyversyteta "Khar'kovskyy polytekhnycheskyy ynstytut" :sb.nauch.trudov:tematycheskyyvыpusk "Systemny analyz, upravlenye y ynformatsyonnыe tekhnolohyy", no. 9, pp. 113–120.
Gaddis, E. S. and Schlünder, E. U. (1979), “Exchange Temperature Distribution and Heat in Multi-Pass Shell-and-TubeExchangers with Baffles”, Heat Transfer Eng., vol. 1, no. 1, pp. 43–52.
Kazancev, E. I. (1975), Promyshlennye pechi: spravochnoe posobie dlja raschetov i proektirovanija[Industrialfurnaces:ahandbook for calculations and design], Metallurgija, Moscow, Russia.
