Evaluation of the Influence on the Efficiency Curvature of the Surface Film Cooling
DOI:
https://doi.org/10.20998/2078-774X.2016.09.07Анотація
The results of numerical simulation of film cooling of the turbine rotor blade with the flow of coolant to the area of the leading edge through three rows of cylindrical holes. To determine the effect of surface curvature on film cooling effectiveness, and a comparison of results obtained with the results of simulation modeling of flow of a plate with film cooling at the inlet cylindrical region. The studies were conducted at the magnitude of the blowing ration of 0.5 to 2.0. Dimensions calculation model and input data received characteristic of the high pressure turbine blades of high-temperature gas turbine engine. Modelling performed using software package ANSYS CFX. The result obtained by calculations that the presence of the cylindrical profiled surfaces instead of flat surface leads to a significant decrease in the average film cooling effectiveness, both cylindrical and the concave surfaces in the investigated range blowing ration values. For all blowing ration film cooling effectiveness parameter values on the suction side is much higher than the pressure side. At the same time, the average efficiency of the film cooling on the suction side when m < 1.5 is higher than on a plot of flat wall, and when m > 1.5 marginally below. Application dependencies obtained on models with flat walls, for the calculation of the film cooling efficiency of suction side and pressure side of the blades is only possible with such amendments as may be determined by the results of this work.
Посилання
Liu, C., Zhu, H. and Zhang, Z. (2012), "Experimental investigation on the leading edge film cooling of cylindrical and laid-backholes with different hole pitches", Turbo Expo 2012, Copenhagen, Denmark, June 11-15,2012,TurbineTechnicalConference&Exposition [Electronic], ASME Paper № GT2012-68027, 12 p.
Sakai, E., Takahashi, T., Funazaki, K., Salleh, H. and Watanabe, K. (2009), "Numerical study on flat plate and leadingedgefilm cooling", ASME ASME Turbo Expo 2009, Orlando, FL USA, June 8-12, 2009, Turbine Technical Conference & Exposition[Electronic], ASME Paper №GT2009-59517, 13 p.
Lokay, V. I., Bodunov, М. N., Dgykov, V. V. and Shukin, A.V. (1985), Teploperedacha v ohlazhdaemyh detaljahgazoturbinnyhdvigatelej letatel'nyh apparatov [Heat transfer in cooled parts of gasturbineenginesofaircraft],Mashinostroenie,Moscow, Russia.
Mick, W. J and Mayle, R. E. (1989), "Zavesnoe ohlazhdenie i teploobmen na lobovoj chasti zatuplennogo tela(vkljuchajauchastok raspolozhenija otverstij vduva) [Stagnation Film cooling and heat transfer, including itseffectwithintheholepatten]",Sovremennoe mashinostroenie, Ser. A, no. 1, pp. 71–80.
Petelchyts, V Y. (2014), "Modelirovanie plenochnogo ohlazhdenija plastiny s vhodnym cilindricheskim uchastkom[CFDSimulation of the Film Deposition of the Plate with Input Cylindrical Section]", Bulletin of NTU “KhPI”.Series:Powerandheatengineeringprocesses and equipment, no. 11(1054), pp. 82–89, ISSN 2078-774X.
Turbulence and Near-Wall Modeling (2014) / ANSYS CFX-Solver Modeling Guide // ANSYS CFX Release 11.0. – ANSYSEuropeLtd. [Electronic]. – P. 97–132. // Modeling Guide // 4. Turbulence and Near-Wall Modeling. – 11.01.2015.
Vargaftik, N. B. (1972), Spravochnik po teplofizicheskim svojstvam gazov i zhidkostej [Handbook of thermophysicalpropertiesof gases and liquids], Fizmatgiz, Moscow. Russia.
